Kramer-electronics TailorMade Manual do Utilizador

1KRAMERElectronicsMATRIX ROUTING SWITCHER

10KRAMERElectronicsMATRIX ROUTING SWITCHERreplies to instructions 10 and 11 are as per the definitions in instructions 7 and 8 respectively. Forexampl

11KRAMERElectronicsMATRIX ROUTING SWITCHERNOTE 10 – POWER ON RESET. The output register has a value under the binar form :1 0 POR1 POR0 P3 P2 P1 P0P3…

12KRAMERElectronicsMATRIX ROUTING SWITCHER3 MATRIX HOOK-UP3.1 MAINS AND GROUND ISOLATIONThe electric ground of all the plugs are the same, but isolate

13KRAMERElectronicsMATRIX ROUTING SWITCHER1- Ground2- Hot3- Cold1- Ground2- Hot3- nc1- Ground2- Hot3- Cold1- Ground2- Hot3- Cold3.4 AUDIOAudio

14KRAMERElectronicsMATRIX ROUTING SWITCHER4 GENERAL FEATURES4.1 VIDEO SECTION- Bandwidth @ -3dB: 325 Mhz- Crosstalk @ 4,43 Mhzes:-60 dB between two

15KRAMERElectronicsMATRIX ROUTING SWITCHER5 TOUCH KEYBOARD : LUMINOUS RE-LABELABLE5.1 PRESENTATIONThe keyboard permits the remote control of the switc

16KRAMERElectronicsMATRIX ROUTING SWITCHER6 INCREMENTAL TOUCH KEYBOARD AND LCD DISPLAY6.1 PRESENTATIONThis keyboard permits the remote control of thes

17KRAMERElectronicsMATRIX ROUTING SWITCHER7 MATRIX_OP4 SOFTWARE7.1 INTRODUCTIONThe principle of the routing switcher is to connecteach of its outputs

18KRAMERElectronicsMATRIX ROUTING SWITCHERA matris routing switcher can contain manydifferents layers, according to the kind of electricsignals :Compo

19KRAMERElectronicsMATRIX ROUTING SWITCHERFour layers can work simultaneously, and each onecan have a different size.7.4.1.1 Names and Connectors capt

2KRAMERElectronicsMATRIX ROUTING SWITCHER

20KRAMERElectronicsMATRIX ROUTING SWITCHERIn this window, choose in the layers that you wantuse, or in the all list, the sources you want. Theswitchin

21KRAMERElectronicsMATRIX ROUTING SWITCHER

22KRAMERElectronicsMATRIX ROUTING SWITCHER

3KRAMERElectronicsMATRIX ROUTING SWITCHERTABLE OF CONTENTS1 HARDWARE ...

4KRAMERElectronicsMATRIX ROUTING SWITCHER1 HARDWARE1.1 GENERALITIESThe Kramer matrix switchers are used to select anddispatch electric signals, as aud

5KRAMERElectronicsMATRIX ROUTING SWITCHER1.3 CREATING A MATRIXThe rear panel of the rack is 84 E wide, on 3RUhigh. (E=5,08 mm). The mains, RS232 and R

6KRAMERElectronicsMATRIX ROUTING SWITCHERthis bus transit the stereo audio signals, and also thepower distribution and the service signals.The cards a

7KRAMERElectronicsMATRIX ROUTING SWITCHER2 COMMUNICATION PROTOCOL “MX06”INCLUDING OPTIONS (02/09/2005 VER-5.06)This RS-232 / RS-485 communication prot

8KRAMERElectronicsMATRIX ROUTING SWITCHER2nd BYTE: Bit 7 – Defined as 1.D6…D0 – “INPUT or DATA”.When switching (ie. instruction codes 1 and 2), the IN

9KRAMERElectronicsMATRIX ROUTING SWITCHER13h 19 53h 83 STORE STATUS Set as SETUP#(0-7)0 - To store1 - To delete01h14h 20 55h 84 RECALL STATUS Set as